OMICRON’s UHF 800 system ensures sensitive partial discharge measurements on gas-insulated switchgear (GIS). This video shows you how the UHF 800 PD measurement and analysis system is easily set up and used on GIS. UHF 800 measures PD in the ultra-high frequency (UHF) range from 100 to 2000 MHz to…
Read more

OMICRON’s UHF 800 system ensures sensitive partial discharge measurements on gas-insulated switchgear (GIS). This video shows you how the UHF 800 PD measurement and analysis system is easily set up and used on GIS. UHF 800 measures PD in the ultra-high frequency (UHF) range from 100 to 2000 MHz to greatly minimize or eliminate interference from external noise in the testing environment – this is especially beneficial during onsite PD measurements. UHF 800 can be used for single-channel or synchronous multi-channel offline and online UHF PD testing on GIS.

Conventional on-site PD measurements, such as those specified by the IEC 60270 standard for high-voltage acceptance testing and troubleshooting, are challenging since they are often affected by noise in the surrounding environment. By comparison, PD measurements performed in the UHF range result in a very high signal-to-noise ratio to enable reliable measurement and analysis. This is because numerous sources of noise, such as mobile communications, radar and corona discharges, are transmitted predominantly in lower or quite narrow frequency ranges. UHF PD measurements in GIS therefore ensure optimal sensitivity with little or no interference from external noise.

OMICRON’s UHF 800 system can also be used for sensitive UHF PD measurements on oil-filled power transformers and high-voltage power cable terminations.

☝️ Learn more about UHF 800 on our website: www.omicronenergy.com/uhf800
☝️ Learn more about PD testing on our website: www.omicronenergy.com/pd-testing
▶️Interested in PD testing? – Watch all of our videos: youtube.com/playlist?list=PLA4B13E71E3A2DF13
_

Would you like to find out more about OMICRON, our passions, and our products?
????Check out our website: www.omicronenergy.com/en

Or follow us on social media
????On LinkedIn: www.linkedin.com/company/omicron-electronics/
????On our podcast Energy Talks: www.omicronenergy.com/en/energy-talks-podcast/
????On YouTube: www.youtube.com/channel/UC2F35zz5XMoi1vbXrMgEyGQ

This video introduces the Linear Dead Tank Transducer, known as the LDTT 300. The video shows how the LDTT 300 is mounted on a circuit breaker. Finally, a test is performed with the CIBANO 500 and the results are analyzed with the Primary Test Manager (PTM) software.

☝️ Learn more about CIBANO 500…
Read more

This video introduces the Linear Dead Tank Transducer, known as the LDTT 300. The video shows how the LDTT 300 is mounted on a circuit breaker. Finally, a test is performed with the CIBANO 500 and the results are analyzed with the Primary Test Manager (PTM) software.

☝️ Learn more about CIBANO 500 on our website: www.omicronenergy.com/en/products/cibano-500/
▶️Interested in Switchgear Testing? – Watch all of our videos: youtube.com/playlist?list=PLzmbZeI1bhu-yEI1tCcZtYM8AIhX-Zh47

_


Would you like to find out more about OMICRON, our passions, and our products?
????Check out our website: www.omicronenergy.com/en

Or follow us on social media
????On LinkedIn: www.linkedin.com/company/omicron-electronics/
????On our podcast Energy Talks: www.omicronenergy.com/en/energy-talks-podcast/
????On YouTube: www.youtube.com/channel/UC2F35zz5XMoi1vbXrMgEyGQ

In this screen video the 4 main new functions of the CT Analyzer Suite 5.20 are explained in detail. For example the multi-test view, the advanced reporting feature, the report template designer, and the simulation feature. Watch now!

00:00 - How to add a license file
01:17 - Multi-Test View
02:27…
Read more

In this screen video the 4 main new functions of the CT Analyzer Suite 5.20 are explained in detail. For example the multi-test view, the advanced reporting feature, the report template designer, and the simulation feature. Watch now!

00:00 - How to add a license file
01:17 - Multi-Test View
02:27 - Advanced Reporting Tool
05:51 - Report Template Designer
08:21 - Simulation Tool

☝️ Learn more about CT Analyzer on our website: www.omicronenergy.com/en/products/ct-analyzer/
☝️ Learn more about Instrument Transformer Testing on our website: www.omicronenergy.com/en/application/offline-testing/instrument-transformer-testing/
▶️Interested in Instrument Transformer Testing with CT Analyzer? – Watch all of our videos: youtube.com/playlist?list=PLzmbZeI1bhu-bwtPfgxqAFE-LyK4DzX0h

_

Would you like to find out more about OMICRON, our passions, and our products?
????Check out our website: www.omicronenergy.com/en

Or follow us on social media
????On LinkedIn: www.linkedin.com/company/omicron-electronics/
????On our podcast Energy Talks: www.omicronenergy.com/en/energy-talks-podcast/
????On YouTube: www.youtube.com/channel/UC2F35zz5XMoi1vbXrMgEyGQ

In this episode, Florian Fink, OMICRON expert for the testing of industrial and distribution grid applications, describes a new automated, close-looped testing approach that has been developed to speed up and enhance the safety and quality of component testing in intelligent secondary distribution…
Read more

In this episode, Florian Fink, OMICRON expert for the testing of industrial and distribution grid applications, describes a new automated, close-looped testing approach that has been developed to speed up and enhance the safety and quality of component testing in intelligent secondary distribution substations (ISDS). He also discusses how this new automated testing method ensures more efficient maintenance and reliable asset operation in rapidly expanding power grids.

We would really like to know what you think about Energy Talks and which topics you would like to hear more about. To do this, simply send us an email to podcast@omicronenergy.com and be sure to give us a star review on Spotify or Apple Podcast. Thanks for your feedback!

Please join us to listen to the next episode of Energy Talks ????️

With software version 4.10, we have improved RelaySimTest in several ways.

The two most important changes include the addition of a new simulation model for an induction motor (or asynchronous motor) and the possibility to simulate infeed events.

With these major additions, you can now test Motor…
Read more

With software version 4.10, we have improved RelaySimTest in several ways.

The two most important changes include the addition of a new simulation model for an induction motor (or asynchronous motor) and the possibility to simulate infeed events.

With these major additions, you can now test Motor Bus Transfer schemes, Motor protection, or Rate of Change of Frequency (ROCOF) protection using the system-based testing approach.

Besides these big changes, a number of smaller improvements have also been made, including improvements of the Interactive System Simulation and the capabilities of RelaySimTest in terms of testing IEC 61850 protection systems.

Learn more about RelaySimTest: www.omicronenergy.com/relaysimtest

For those who were not able to attend the CIGRE 2022 conference and exhibition in Paris, France, we are devoting two episodes of Energy Talks to share various impressions of this leading power systems industry event with you.

In Part 1, OMICRON event specialist Aby-Gael Meyet interviews Philippe…
Read more

For those who were not able to attend the CIGRE 2022 conference and exhibition in Paris, France, we are devoting two episodes of Energy Talks to share various impressions of this leading power systems industry event with you.

In Part 1, OMICRON event specialist Aby-Gael Meyet interviews Philippe Adam, Secretary General at CIGRE, to find out more about CIGRE as an organization, the significance of this year’s event, as well as important industry topics addressed at CIGRE 2022.

For a complete schedule of upcoming events where you can meet OMICRON in person or online, be sure to check out our Events Calendar: www.omicronenergy.com/en/events/overview/
Enjoy listening!

We would really like to know what you think about Energy Talks and which topics you would like to hear more about. To do this, simply send us an email to podcast@omicronenergy.com and be sure to give us a star review on Spotify or Apple Podcast. Thanks for your feedback!

Please join us to listen to the next episode of Energy Talks ????️

In this episode of Energy Talks, OMICRON Field Testing Experts Mohamed Ali, Fadi Zatari and Ahmed Abdelwahab highlight the specific power system testing challenges in Middle East countries. They also offer examples of how portable, battery-powered and multi-functional testing solutions, such as…
Read more

In this episode of Energy Talks, OMICRON Field Testing Experts Mohamed Ali, Fadi Zatari and Ahmed Abdelwahab highlight the specific power system testing challenges in Middle East countries. They also offer examples of how portable, battery-powered and multi-functional testing solutions, such as OMICRON’s COMPANO 100, are helping field engineers to greatly simplify power system testing in the region.

???? Learn more about COMPANO 100 here: omicronenergy.com/compano100


We would really like to know what you think about Energy Talks and which topics you would like to hear more about. To do this, simply send us an email to podcast@omicronenergy.com and be sure to give us a star review on Spotify or Apple Podcast. Thanks for your feedback!

Please join us to listen to the next episode of Energy Talks ????️

The optimal quality of power system measurement data is essential for making reliable condition assessments of electrical equipment and predicting asset lifetime. In this episode, David Gopp, Data Scientist and Digital Transformation Expert at OMICRON, discusses how artificial intelligence is…
Read more

The optimal quality of power system measurement data is essential for making reliable condition assessments of electrical equipment and predicting asset lifetime. In this episode, David Gopp, Data Scientist and Digital Transformation Expert at OMICRON, discusses how artificial intelligence is effectively used to perform pattern recognition on measurement data to identify irregularities and to help users validate the accuracy of their measurements for more reliable assessments.

We would really like to know what you think about Energy Talks and which topics you would like to hear more about. To do this, simply send us an email to podcast@omicronenergy.com and be sure to give us a star review on Spotify or Apple Podcast. Thanks for your feedback!

Please join us to listen to the next episode of Energy Talks ????️

The conventional method for PD measurement according to the IEC 60270 standard allows a precise calibration but requires a sufficiently high signal-to-noise ratio (SNR) in the measurement circuit – this is however very difficult to obtain when performing PD measurements on site.

In this episode of…
Read more

The conventional method for PD measurement according to the IEC 60270 standard allows a precise calibration but requires a sufficiently high signal-to-noise ratio (SNR) in the measurement circuit – this is however very difficult to obtain when performing PD measurements on site.

In this episode of Energy Talks, OMICRON PD application expert Ulrike Broniecki discusses how partial discharge (PD) measurements performed in the ultra-high frequency (UHF) range can be a reliable complementary or alternative solution to conventional PD testing in noisy onsite testing environments. She also highlights the benefits of using the UHF PD measurement method on gas-insulated switchgear (GIS), gas-insulated lines (GIL), oil-filled transformers and high-voltage power cable terminations.

Learn more about our new UHF 800 here: omicronenergy.com/uhf800

We welcome your questions and feedback. Simply send us an email to
???? podcast@omicronenergy.com

Please join us to listen to the next episode of Energy Talks ????️

Digital Transformation in the Power Industry is the theme of our new Energy Talks podcast miniseries with various episodes about the process of using digital technologies to enhance business processes and customer experiences in the power industry.

In Part 2 of our Energy Talks miniseries, OMICRON…
Read more

Digital Transformation in the Power Industry is the theme of our new Energy Talks podcast miniseries with various episodes about the process of using digital technologies to enhance business processes and customer experiences in the power industry.

In Part 2 of our Energy Talks miniseries, OMICRON digital transformation experts Juan Carlos Sánchez and Lukas Klingenschmid discuss the specific challenges companies in the power industry are facing in making a successful digital transformation, and what solutions are available to overcome them.

They highlight success factors, such as using digital technologies and processes to simplify data gathering and accessibility to reliable data, employing cyber security practices, improving digital skills and fostering an organizational culture that welcomes change.

We welcome your questions and feedback. Simply send us an email to
???? podcast@omicronenergy.com

Please join us to listen to the next episode of Energy Talks ????️